-
-
Olive Oil Decanters » PMS 250/ PX 05
- Type
- :
- PX 05
- Body Steel
- :
- AISI 316 Ti – 1.4571 ( DIN )
- Screw Material
- :
- AISI 316 Ti – 1.4571 ( DIN )
- Screw coating material
- :
- Tungsten carbide
- Screw coating hardness
- :
- 60-65 HRC
- Hardness thickness
- :
- 2.5 mm
- Screw length
- :
- 630 mm
- Drum diameter
- :
- 254 mm
- Motor brand, power, speed
- :
- 5.5 kW , 3000d/d
- Gear box type
- :
- Cycloid
- Reduction rate
- :
- 25 / 1
- Max. rotation
- :
- 4500 d/d
- Operation rotation
- :
- 4300 d/d
- Elec. Motor operating system
- :
- Invertör
- Drum thickness
- :
- 8 mm
- Drum length
- :
- 780 mm
- Feeding material for drum
- :
- Zeytin Hamuru
- Maximum operating temperature
- :
- 60°C
- Specific density of feeding material for drum (max)
- :
- 1,3kg / dm3
The drum rotation of 4500 rpm is powered by a invertor driven motor. As a result, centrifugal forces keep the oil production at the maximum level and thus, the system separates the crude paste, water and the olive oil from each other according to their specific gravity.
The paste, carried by the mono pump and the 35º - 38º warm water from the flow meter are entering the decanter drum together. The water is carried out to the lower unit of the decanter from the entrance channel behind the drum and then it is sent to the vibrated sieve near the decanter. The oil within the drum is specially designed and it is taken out of the drum by 2 burners located opposite to each other. The oil entering the lower unit of the decanter helps to discharge the paste out of the system by creating a transfer differention through vibration.
A gearbox, in front of the drum helps to discharge the solid out of the system by creating a transfer differention between the drum and screw. Screw coils are covered with 2,5 mm think tungsten carbure of 60-65 Rockwell.
The aim here is to minimize the abrasion which may occur in time. All surfaces and the equipment the olive paste touches as it enters in to the decanter are made out of inox materials according to the good regulations.In order to avoid the paste being stuck at the surface while it goes out the drum, a cleaning system is established at the front part of the drum. Against any jamming, a speed control system is used which will operate the paste pump during the operation of the decanter. The main frame which provides embedding for the decanter drum is produced out of St 37 materials.
The main characteristics of Polat Machine decanter which distinguishes it from the others are as follows:
- The decanter which operates in 3 phases can carry out the production with 2 phases by choosing the adjustable water exit channels when required. It does not require any additional parts and expenditures.
- The water palette at the final point of the screw within the decanter prevents the oil from being mixed with the black water.
- The paste amount in the oil can be adjusted by the adjustable oil exit channels located on the body.
- Oil and water discharging ways are adjusted according to the olive sort.
- It is resistant to the sudden shocks at a ratio of % 500 thanks to the structure of gear box and the gearbox can absorb the sudden starting and stopping strikes.10 years guaranty.
It keeps the maximum capacity at the level it is adjusted by the means of PLC control system.
- An inverter, installed to the system will not let affect the electrical undulation.
The machine owns an electronic aided protection system designed to avoid damages under excessive loading and sudden shocks.
Why POLAT MAKINA A.S. is using one separator?
Because oil percent in dirty water discharged from decanter is max. 0.5 gr/lt, so there is no need for a second separator. -
